DELTAShield CRX 700

DELTAShield CRX 700

VIEW OUR PROJECT REFERENCES

MERCEDES TRUCK BUMPERS

Location: Egypt

PLOUGHING SPIRALS

Location: India

SPRAY IN CASTABLE MOULDS

Location: -

Description

DELTAShield CRX 700 is a specially formulated high performance, rigid polymer designed for in mold spray applications, mold making applications and the replacement of fiberglass reinforcing.

DELTAShield CRX 700 exhibits excellent structural strength, good thermal stability and very low moisture permeability making it suitable for use in immersion applications.

DELTAShield CRX 700 is spray applied and is tack free in seconds providing very rapid turn around and handling times.

Features

  • Extremely fast application
  • Extremely fast cure resulting in reduced handling and re-use times
  • Good abrasion resistance
  • Excellent adhesion
  • Very good impact resistance
  • Excellent chemical resistance
  • Very low moisture absorption
  • Stable over a wide temperature range

Typical Uses

  • Fabrication of parts traditionally made from Fibreglass
  • In mould spraying of components
  • Structural support of flexible wear linings
  • Structural support of vacuum formed components
Orders & EnquiriesDownload Datasheet

View more information

Processing Properties

PROCESSING PROPERTIES DATA
Chemical base Polyurethane / Polyurea hybrid technology
Mixing ratio of Comp. A to Comp. B 1 : 1 by volume
Dry film thickness range [mm]

For project specific DFT recommendations consult with manufacturer.

 Steel Minimum: 0.75           Maximum: indefinite
Recommended thickness [mm] Minimum: 0.75 – 1               Maximum: unlimited
Tack Free-Time at 20°C [sec.] 60 – 90
Over coat cycle [h] 0 – 8 (without any pre-treatment)
Curing/loading after [h] Walkable: 1          Mechanical: 2          Chemical: 12 – 24
Temperature range for application (ambient) [°C] -10 – +60
Temperature range for application (substrate) [°C] -5 – +75
Temperature range for service [°C] -40 – +150
Material Temperature (Preconditioning) [°C] 30° – 40°
Material Temperature (Spraying) [°C] 60 – 75
Maximal relative air humidity for application [%] 95
Pay attention to the dew point limit Substrate should be 3C greater than DP (dew point)

Physical Properties

PHYSICAL PROPERTIES DATA
VOC-content DIN EN ISO 11890-1 / ASTM D-1259 0
Solids content DIN EN 827 / ASTM D-2697 100
Tensile strength [MPa] DIN ISO EN 572 45
Flexural Modulus (KPSI) ASTM D-790 225 – 275
Elongation at break [%] DIN ISO EN 572 6
Hardness [Shore D] DIN ISO EN 572 70 ± 5

 

PHYSICAL PROPERTIES DATA
Impact resistance EN 10290 23° C – 14 J/mm
Specific Electrical Insulation resistance. EN 10290 23 °C – 100 days >110 Ωm2

80 °C – 30 days >108 Ωm2
Taber Abrasion [mg] ASTM D-4060 < 110 (Wheel H18 / 1.000g / 1000 Cycles)
Adhesion – Pull off strength EN 10290 23° C ≥ 14 mpa

70° C – 7 days – 5% NaCl ≥ 8 mpa
Cathodic Disbondment ASTM G42 80° C (14 days): 6mm
Resistance to Root Penetration EN 14416 Passed
Flexibility EN 10290 Passed
Indentation Resistance EN 10290 23° C < 0.15mm

80° C < 20%
Immersion in Sea Water – 90 days Internal 80° C – 90 days PASS
Storage conditions [°C] DIN EN 12701 10 – 30 (in closed original drums, stored at dry and well-ventilated place; beware of freezing)
Gouge test CAN/CSA Z245.21-10 50 Kg, indentation 28 %
Gouge test CAN/CSA Z245.21-10 70 Kg, indentation 50 %
Shelf life – Approximately 12 months unopened and stored correctly