DELTAShield CRX 700

DELTAShield CRX 700

VIEW OUR PROJECT REFERENCES
Description
DELTAShield CRX 700 is a specially formulated high performance, rigid polymer designed for in mold spray applications, mold making applications and the replacement of fiberglass reinforcing.
DELTAShield CRX 700 exhibits excellent structural strength, good thermal stability and very low moisture permeability making it suitable for use in immersion applications.
DELTAShield CRX 700 is spray applied and is tack free in seconds providing very rapid turn around and handling times.
Features
- Extremely fast application
- Extremely fast cure resulting in reduced handling and re-use times
- Good abrasion resistance
- Excellent adhesion
- Very good impact resistance
- Excellent chemical resistance
- Very low moisture absorption
- Stable over a wide temperature range
Typical Uses
- Fabrication of parts traditionally made from Fibreglass
- In mould spraying of components
- Structural support of flexible wear linings
- Structural support of vacuum formed components
View more information
Processing Properties
PROCESSING PROPERTIES | DATA |
Chemical base | Polyurethane / Polyurea hybrid technology |
Mixing ratio of Comp. A to Comp. B | 1 : 1 by volume |
Dry film thickness range [mm]
For project specific DFT recommendations consult with manufacturer. |
Steel Minimum: 0.75 Maximum: indefinite |
Recommended thickness [mm] | Minimum: 0.75 – 1 Maximum: unlimited |
Tack Free-Time at 20°C [sec.] | 60 – 90 |
Over coat cycle [h] | 0 – 8 (without any pre-treatment) |
Curing/loading after [h] | Walkable: 1 Mechanical: 2 Chemical: 12 – 24 |
Temperature range for application (ambient) [°C] | -10 – +60 |
Temperature range for application (substrate) [°C] | -5 – +75 |
Temperature range for service [°C] | -40 – +150 |
Material Temperature (Preconditioning) [°C] | 30° – 40° |
Material Temperature (Spraying) [°C] | 60 – 75 |
Maximal relative air humidity for application [%] | 95 |
Pay attention to the dew point limit | Substrate should be 3C greater than DP (dew point) |
Physical Properties
PHYSICAL PROPERTIES | DATA | ||
VOC-content | DIN EN ISO 11890-1 / ASTM D-1259 | 0 | |
Solids content | DIN EN 827 / ASTM D-2697 | 100 | |
Tensile strength [MPa] | DIN ISO EN 572 | ≥ 45 ± 5 | |
Flexural Modulus (KPSI) | ASTM D-790 | 225 – 275 | |
Elongation at break [%] | ASTM D-638-22 | 5 – 8 | |
Hardness [Shore D] | STM D-2240-15(2021) | 70 ± 5 |
PHYSICAL PROPERTIES | DATA | |
Impact resistance | EN 10290 | 23° C – 14 J/mm |
Specific Electrical Insulation resistance. | EN 10290 | 23 °C – 100 days >110 Ωm2
80 °C – 30 days >108 Ωm2 |
Taber Abrasion [mg] | ASTM D-4060-19 | < 110 (Wheel H18 / 1.000g / 1000 Cycles) |
Adhesion – Pull off strength | ASTM D-4541 | 23° C ≥ 14 mpa
70° C – 7 days – 5% NaCl ≥ 8 mpa |
Cathodic Disbondment | ASTM G42 | 80° C (14 days): 6mm |
Resistance to Root Penetration | EN 14416 | Passed |
Flexibility | EN 10290 | Passed |
Indentation Resistance | EN 10290 | 23° C < 0.15mm
80° C < 20% |
Immersion in Sea Water – 90 days | Internal | 80° C – 90 days PASS |
Storage conditions [°C] | DIN EN 12701 | 10 – 30 (in closed original drums, stored at dry and well-ventilated place; beware of freezing) |
Gouge test | CAN/CSA Z245.21-10 | 50 Kg, indentation 28 % |
Gouge test | CAN/CSA Z245.21-10 | 70 Kg, indentation 50 % |
Shelf life | – | Approximately 12 months unopened and stored correctly |
Safety & Handling
All applicators of C R X 7 00 should be trained and approved by the manufacturer
• Spray applicators should wear appropriate PPE including approved breathing equipment, eye wear, Nylex or similar light weight spray suit and appropriate covered footwear
• Avoid breathing in vapors during spraying or when handling chemicals
• Avoid eye and skin contact
• Store chemical drums in a cool dry environment. Avoid storing chemicals for long periods in direct sunlight
• Do not store chemicals next to food stuffs
• Ensure chemical drums are kept tightly sealed and avoid ingress of air and moisture
Technical Services
Detailed technical assistance and further information regarding this system and its relevant application specifications are available from DELTA Technical Services
Packaging
Is supplied in 40 or 490 kg sets.
• Component A : 20 or 210 kg
• Component B : 20 or 280 kg
All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user`s responsibility to satisfy himself, by his own investigations and testing, the suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. Due to the large number of variables that can affect the product and the application process that are out of the control of DELTA Coatings International LLC no warranty of any kind, express or implied is given. The liability of DELTA Coatings International LLC for any claims is limited to the purchase value of the material.



